Tips for Pattern Creation

How to Create Orthotic Patterns With the Use of a Paper Towel

Before moulding any thermoplastic material on your patient’s hand, it is recommended and helpful to begin with a pattern.
A pattern allows you to judge the correct amount of material needed for the specific orthosis and helps you to envision the shape and position of the finished product.

We begin by placing the patient’s hand palmar side down on a paper towel. If the patient cannot place their involved hand on the paper towel, you can always draw an outline of the non-involved hand or draw a pattern of your own hand. Adjustments can be made directly on the paper towel prior to cutting out the thermoplastic material.

Place the hand in a neutral wrist position, with the fingers close together and the thumb in wide abduction.

 

Drawing the Patient’s Hand

  1. Make sure that your patient’s hand is placed in a neutral wrist position and not radially or ulnarly deviated. You can assess this by checking for straight alignment of the forearm bones with the third metacarpal.
  2. Place the fingers close together and the thumb in wide abduction.
  3. Draw an outline of the forearm, wrist, thumb and fingers with the pen or marker angled straight down on the paper.

There are several methods to add additional width to the forearm lines on the radial and ulnar sides to make sure the pattern has enough material to wrap around the forearm:

  • Redraw the forearm lines with the pen angled at a 45° angle to the arm.
  • Add about 2,5 cm/1” width to the previously drawn forearm lines.
  • Add 2-3 fingers’ width to the previously drawn forearm lines.

These measures ensure that the pattern (and subsequently the orthosis) has enough material to adequately cover 1/2 of the circumference of the forearm.

 

Anatomical Landmarks

Mark the relevant anatomical landmarks which will aid in determining the proximal and distal edges of the orthosis. Because we are looking at the dorsal hand, we have to imagine where the volar landmarks are placed.

The most helpful anatomical landmarks to mark include, but are not limited to, the following:

  • At 2/3 the length of the forearm – mark both radial and ulnar sides.
  • The MCP joints of the little and index fingers – The MCP joints of the little and index fingers help to find the distal palmar crease, which is angled to the ulnar side.
  • The first web space – often a thin wedge of thermoplastic material wraps around through this web space to anchor the orthosis.
  • The narrowest part of the wrist – adjust the width of the pattern to accommodate to the narrow wrist or else you will have to do a lot of trimming.
  • The thumb IP joint – thumb orthoses typically allow for unrestricted IP joint motion.
  • The PIP joints of each finger – MCP joint blocking orthoses typically allow unrestricted PIP motion.

 

Adjustments to the Pattern

After drawing the relevant anatomical landmarks, remove the patient’s hand and draw your specific orthosis pattern lines. The pattern itself may come from a picture or from your own idea of which specific joints need to be included in the orthosis.

Cut out the pattern and check the fit on the patient’s hand in the desired position. Draw any additional markings on the pattern to indicate necessary adjustments. You can add arrows to increase length or width, or make lines indicating where the pattern needs to be trimmed or shortened.

Making adjustments to the pattern will save time and cost when cutting out the thermoplastic material.

 

Cutting out the Pattern

Once you have checked the paper towel pattern for fit, place it on an appropriately sized piece of thermoplastic material. Draw an outline, but leave enough space for cutting away the marked lines. These should not appear on the finished orthosis. You can use this marker to draw the outline, it will easily wipe off later on.

Prior to cutting out the material, determine whether you should preheat it.

  • 3 mm (1/8”) thick material is best cut when slightly warm.
  • 2 mm (1/12”) thick material may need only slight heating for ease of cutting.
  • 1,6 mm (1/16”) thick material is best cut without heating at all.

Activate the material and place the patient’s hand in the desired position. Mould the material to the patient’s hand just like you fitted the paper towel pattern previously.

A well-drawn pattern will translate to an orthosis that requires only minimal trimming for a great fit.

 

Written by Debby Schwartz, OTD, OTR/L, CHT

Physical Rehabilitation Product and Educational Specialist at Orfit Industries America.

Debby is a hand therapist with over 34 years of clinical experience. She completed her Doctorate of Occupational Therapy at Rocky Mountain University of Health Professions in 2010.

She is also an adjunct professor at the Occupational Therapy Department of Touro College in NYC and has written many articles for hand therapy journals, including the ASHT Times and the Journal of Hand Therapy.

 

 

Contact us for more product information or find your local distributor here.

 

If you’d like to receive the latest product updates and interesting Orfit news, subscribe to our newsletter:

Subscribe to our mailing list

* indicates required
Select your preferred newsletters

The protection of your personal data is our priority. Thank you for subscribing to one of our newsletters. We would like to invite you to share some personal data with us. The protection of this data is our priority.

By submitting this form, I agree to the processing of my data to receive personal messages by mail.

You can change your mind at any time by clicking the unsubscribe link in the footer of any email you receive from us, or by contacting us at welcome@orfit.com. We will treat your information with respect. For more information about our privacy practices please visit our website. By clicking below, you agree that we may process your information in accordance with these terms.

We use MailChimp as our marketing automation platform. By clicking below to submit this form, you acknowledge that the information you provide will be transferred to MailChimp for processing in accordance with their Privacy Policy and Terms.

We've selected some similar articles for you

Orthotic Fabrication for Musicians

Keep the Music Playing!

Musicians may experience different types of repetitive strain or overuse injuries. Some may even have to stop playing their beloved instrument due to these issues. Fortunately, there are a number of ways in which therapists can help musicians. They can provide custom orthoses which may be very beneficial to both professional and amateur music makers.
Read more

Congratulations to the new CHT’s!

Orfit is proud to acknowledge the 133 newly Certified Hand Therapists (CHT’s) who passed the November 2016 Hand Therapy Certification Examination. Many hours of study and hard work went into their success. These committed individuals are occupational or physical therapists with at least 5 years of clinical experience, including 4000…
Read more

Choosing the Perfect Material for your Orthosis

The most appropriate material for effective orthotic fabrication

Choosing an appropriate thermoplastic material is one of the most important aspects of orthotic fabrication. If you understand the properties and possibilities of each material, you will always be able to select the perfect material.
Read more