The Orficast Full Finger Wrap

Guidelines and directions for the full finger wrap

The Full Finger Wrap is an easy and versatile orthosis you can make in just a few minutes. It quickly immobilizes the affected digits and places them in a position for healing. It is ideal for all fingers, including the thumb, and toes.

You can use wrap orthosis for a variety of indications, from sprains to fractures, and it is also very suitable for serial casting.

Keep the following tips and directions in mind for the best orthotic fabrication results.

Go straight to the instructional video

 

How to make a Full Finger Wrap?

We recommend using Orficast 3 cm (1”) for this orthosis. Its tape-like properties make it easy to effectively wrap the material around the affected digit and keep it in place.

Closely follow the directions and take care that you do not make the orthosis too thick or bulky.

Step 1: Take a piece of Orficast 3 cm (1”) about 20-22 cm (8-9”) long. Activate it in hot water and pat dry briefly, maintaining most of the heat.

Measuring Orficast for the full finger wrap

 

Step 2: Now you can start wrapping the material around the digit. Start distally at the fingertip and anchor the first wrap around to the next layer of material. Wrap at an angle and overlap the previous layer by 50%.

Continue wrapping as you would do with Coban wrap for oedema control. Finish at the web space and secure the corners of the Orficast to the layer underneath.

 

Step 3: Make sure that the surface of the wrap is smooth. Rub your fingers over the wrapped material to secure all layers together.

 

Step 4: Now you can place the finger in the desired extended position. Keep the MCP joint flexed and hold the PIP in maximal tolerable end range by holding underneath the distal fingertip. Do not press on the dorsal PIP joint.

You can keep the DIP joint in the orthosis or leave it out.

Finished full finger wrap in Orficast Blue

 

How to use the full finger wrap for serial casting?

Serial static orthoses hold a stiff joint or tight shortened tissue in its end range position to increase passive range of motion or tissue length.

Every few days or even once a week, the therapist removes the orthosis and performs treatment to the stiff or contracted joint. Then they apply a new orthosis to the client in a new end range position.

Removing the orthosis

First, the patient should try and see if they can remove the wrap themselves. Have them tug slightly at the orthosis after it has hardened, and it might just pull off.

If not, the orthosis is easily cut with small curved scissors or plaster scissors down one side. You can have the patient soak the finger in warm water for about 15 minutes, and then try to pull it off. The warm water will loosen the orthosis slightly, but it will not change the shape.

.

Instructional Video

In this video, we explain how to create a full finger wrap that includes the DIP joint:

 

Questions?

If you have a question or comment, please post it in the Orfit Splinting & Rehabilitation Group on Facebook, or send an email to welcome@orfit.com

 

Written by Debby Schwartz, OTD, OTR/L, CHT

Physical Rehabilitation Product and Educational Specialist at Orfit Industries America.

Debby is a certified hand therapist with over 36 years of clinical experience. She completed her Doctorate of Occupational Therapy at Rocky Mountain University of Health Professions in 2010. She has worked at Orfit Industries America as Product and Educational Specialist since 2007.

Debby is also an adjunct professor at the Occupational Therapy Department of Touro University, School of Health Sciences, and at the Occupational Therapy Department at Yeshiva University, Katz School of Science and Health in NYC. She has written many book chapters in the field of hand therapy and multiple articles for hand therapy journals, including the ASHT Times and the Journal of Hand Therapy. She has published a new textbook on orthotic fabrication together with Dr. Katherine Schofield, entitled “Orthotic Design and Fabrication for the Upper Extremity: A Practical Guide”.

Debby’s Google Scholar

 

If you’d like to receive the latest product updates and interesting Orfit news, subscribe to our newsletter:

We've selected some similar articles for you
Comfortable and lightweight orthoses with Orfilight NS
When patients are required to wear their orthoses for long duration during day and night, it is always helpful to consider the size of the patient’s extremity, the specifics of the diagnosis and the weight of the selected material for the orthosis. Orfit offers Orfilight, an extremely lightweight material that might be appropriate for many of your patients, regardless of the specific diagnosis.
Read more
Hand Therapy for Cyclists
Advice on orthoses and other strategies to reduce symptoms of peripheral neuropathies
A recently published systematic review in the Journal of Hand Therapy highlights other strategies to reduce and avoid symptoms of peripheral neuropathies in cyclists. Let's unpack their findings and look at a helpful orthotic fabrication idea for cyclists.
Read more
New Technique for Attaching Hook-and-Loop Straps to Orficast
Attaching straps with the help of Edging Strip
We share a new, quick, and easy method to attach straps to Orficast! We will be using an unexpected ally for an unbreakable bond: Thermoplastic Edging Strip.
Read more